Improving the Lateral-Resistant Behavior of Steel Plate Shear Walls with CFST Columns Using Two-Layer Flat-Corrugated Plates

Authors

  • Huanqing Jiang Hunan Urban Construction College, Xiangtan, Hunan 411100, China
  • Dongyu Ji Henan Institute of Energy and Chemical Technology, Puyang, Henan 457000, China
  • Xingpei Wang Hunan Urban Construction College, Xiangtan, Hunan 411100, China

DOI:

https://doi.org/10.13052/ejcm2642-2085.3531

Keywords:

flat-corrugated SSW, CFST, hysteresis curve, resistance, energy dissipation

Abstract

Utilizing flat plates (FPs) in a steel plate shear wall (SPSW) system significantly pinches the hysteresis curves, as these plates are highly susceptible to out-of-plane buckling. In this study, a flat-corrugated plate (FCP) was used in an SPSW system with concrete-filled steel tubes (CFST) columns. In this study, an earlier evaluated traditional flat SPSW with CFST columns was validated in ABAQUS software under cyclic loads. Then, by introducing a two-layer FCP that encompasses both a flat and a trapezoidal corrugated plate, instead of an flat plate (FP), the effects on the hysteresis curve and structural parameters were investigated. The results showed that using an FCP instead of a traditional FP in an SPSW system (FCSPSW) with CFST columns led to a fatter hysteresis curve and, subsequently, a significant improvement in energy dissipation. The maximum resistance of the FCSPSWs with CFST columns was slightly higher than that of the control sample. The results showed that the use of an FCP has a minimal effect on the elastic stiffness.

Downloads

Download data is not yet available.

Author Biographies

Huanqing Jiang, Hunan Urban Construction College, Xiangtan, Hunan 411100, China

Huanqing Jiang graduated from Wuhan University of Technology, China, in 2012. She works at Hunan Urban Construction College. Her research interests lie in the design of concrete structures and steel structures.

Dongyu Ji, Henan Institute of Energy and Chemical Technology, Puyang, Henan 457000, China

Dongyu Ji graduated from North China University of Water Conservancy and Electric Power, China, in 2007. He currently works at Henan Institute of Energy and Chemical Technology. His research interests include engineering structural design and numerical simulation analysis.

Xingpei Wang, Hunan Urban Construction College, Xiangtan, Hunan 411100, China

Xingpei Wang graduated from the Shanghai University, China, in 2012. He works at Hunan Urban Construction College. His research interests include geotechnical engineering and construction technology.

References

M. G. Azandariani, M. Gholhaki, and M. A. Kafi, “Experimental and numerical investigation of low-yield-strength (LYS) steel plate shear walls under cyclic loading,” Engineering Structures, vol. 203, p. 109866, 2020, doi: 10.1016/j.engstruct.2019.109866.

B. Shekastehband, A. Azaraxsh, and H. Showkati, “Experimental seismic study on shear walls with fully-connected and beam-only-connected web plates,” Journal of Constructional Steel Research, vol. 141, pp. 204–215, 2018, doi: 10.1016/j.jcsr.2017.11.013.

T. Rakan-Nasrabadi, S. Pourmahdi-Tazeabadi, S. Karimi-Gabalou, and A. Haghollahi, “Investigating lateral behavior of the hybrid system of flat steel shear walls and cold-formed S-shaped steel plate dampers under cyclic loading,” Iranian Journal of Science and Technology, Transactions of Civil Engineering, pp. 1–25, 2024.

S. Pourmahdi, T. Rakan-Nasrabadi, and K. Cheraghi, “Numerical study of cyclic behavior of single-layer flat-corrugated steel shear walls,” Asian Journal of Civil Engineering, pp. 1–20, 2025.

H. Takabatake, T. Nonaka, and T. Tanaki, “Numerical study of fracture propagating through column and brace of Ashiyahama residential building in Kobe Earthquake,” The Structural Design of Tall and Special Buildings, vol. 14, no. 2, pp. 91–105, 2005.

D.-H. Shin and H.-J. Kim, “Post-buckling strengths of steel-plate shear walls with two-side clamped boundary conditions,” Thin-Walled Structures, vol. 170, p. 108499, 2022, doi: 10.1016/j.tws.2021.108499.

M. Elgaaly, V. Caccese, and C. Du, “Postbuckling behavior of steel-plate shear walls under cyclic loads,” Journal of Structural Engineering, vol. 119, no. 2, pp. 588–605, 1993, doi: 10.1061/(ASCE)0733-9445(1993)119:2(588).

J. W. Berman, “Seismic behavior of code designed steel plate shear walls,” Engineering Structures, vol. 33, no. 1, pp. 230–244, 2011, doi: 10.1016/j.engstruct.2010.10.015.

J. Lindner, “Shear capacity of beams with trapezoidally corrugated webs and openings,” in Proceedings of Structure Stability Research Council, Chicago, 1991.

M. Elgaaly, R. W. Hamilton, and A. Seshadri, “Shear strength of beams with corrugated webs,” Journal of Structural Engineering, vol. 122, no. 4, pp. 390–398, 1996.

Q. Cao and J. Huang, “Experimental study and numerical simulation of corrugated steel plate shear walls subjected to cyclic loads,” Thin-Walled Structures, vol. 127, pp. 306–317, 2018, doi: 10.1016/j.tws.2018. 01.042.

Q. Cao, J. Huang, B. Gu, D. Li, and J. Huang, “Experimental and numerical study on hysteretic behaviour of corrugated steel plate shear walls under lateral loads,” Journal of Building Engineering, vol. 82, p. 108297, 2024, doi: 10.1016/j.jobe.2023.108297.

J. Tong, R. Wu, and L. Wang, “Experimental and numerical investigations on seismic behavior of stiffened corrugated steel plate shear walls,” Earthquake Engineering & Structural Dynamics, vol. 52, no. 12, pp. 3551–3574, 2023, doi: 10.1002/eqe.3920.

W. Wang, C.-C. Quan, Y. Li, G.-K. Zhen, and H.-T. Zhao, “Experimental study and numerical simulation analysis on seismic performance of corrugated steel-plate shear wall with replaceable bottom corner dampers,” Soil Dynamics and Earthquake Engineering, vol. 152, p. 107061, 2022, doi: 10.1016/j.soildyn.2021.107061.

W. Wang, Y. Ren, Z. Lu, J. Song, B. Han, and Y. Zhou, “Experimental study of the hysteretic behaviour of corrugated steel plate shear walls and steel plate reinforced concrete composite shear walls,” Journal of Constructional Steel Research, vol. 160, pp. 136–152, 2019, doi: 10.1016/j.jcsr.2019.05.019.

C.-B. Wen, J.-Q. Zuo, Y.-L. Guo, X. He, H.-J. Sun, and J.-S. Duan, “Experimental and numerical study on seismic behaviors of corrugated plate shear walls,” Journal of Constructional Steel Research, vol. 229, p. 109496, 2025, doi: 10.1016/j.jcsr.2025.109496.

F. Emami, M. Mofid, and A. Vafai, “Experimental study on cyclic behavior of trapezoidally corrugated steel shear walls,” Engineering Structures, vol. 48, pp. 750–762, 2013.

J. Qiu, Q. Zhao, C. Yu, and Z. Li, “Experimental studies on cyclic behavior of corrugated steel plate shear walls,” Journal of Structural Engineering, vol. 144, no. 11, p. 04018200, 2018, doi: 10.1061/(ASCE)ST.1943-541X.0002165.

C.-B. Wen, B.-L. Zhu, H.-J. Sun, Y.-L. Guo, W.-J. Zheng, and L.-L. Deng, “Global stability design of double corrugated steel plate shear walls under combined shear and compression loads,” Thin-Walled Structures, vol. 199, p. 111789, 2024, doi: 10.1016/j.tws.2024.111789.

V. Broujerdian, A. Ghamari, and A. Abbaszadeh, “Introducing an efficient compound section for steel shear wall using flat and corrugated plates,” Structures, vol. 33, pp. 2855–2871, 2021.

I. H. Nayel, A. Ghamari, and V. Broujerdian, “On the behavior of an innovative four-layer semi-supported steel plate shear wall,” Case Studies in Construction Materials, vol. 17, p. e01427, 2022, doi: 10.1016/j.cscm.2022.e01427.

A. Abbaszadeh, A. Ghamari, and V. Broujerdian, “Seismic behavior of an innovative four-layer steel shear wall,” KSCE Journal of Civil Engineering, vol. 27, no. 11, pp. 4770–4786, 2023, doi: 10.1007/s12205-023-1419-8.

C. Dou, C. Xie, Y. Wang, and N. Yang, “Cyclic loading test and lateral resistant behavior of flat-corrugated steel plate shear walls,” Journal of Building Engineering, vol. 66, p. 105831, 2023, doi: 10.1016/j.jobe.2023.105831.

J.-K. Tan, X.-H. Zhou, X. Nie, Y.-H. Wang, and K. Wang, “Experimental and numerical investigation of cross-shaped buckling-restrained SPSWs with composite structure,” Journal of Building Engineering, vol. 47, p. 103873, 2022.

J.-G. Nie, H.-S. Hu, J.-S. Fan, M.-X. Tao, S.-Y. Li, and F.-J. Liu, “Experimental study on seismic behavior of high-strength concrete filled double-steel-plate composite walls,” Journal of Constructional Steel Research, vol. 88, pp. 206–219, 2013.

Y. Cai, M. Su, X. Chen, and B. Young, “High strength steel square and rectangular tubular stub columns infilled with concrete,” Journal of Constructional Steel Research, vol. 179, p. 106536, 2021.

J. Shi, L. Guo, and B. Qu, “In-plane cyclic tests of double-skin composite walls with concrete-filled steel tube boundary elements,” Engineering Structures, vol. 250, p. 113301, 2022.

J.-K. Tan, X.-H. Zhou, H. Su, Y.-H. Wang, T. Zhou, and K. Wang, “Interaction behaviour of buckling-restrained steel plate shear wall and boundary composite frame,” Journal of Constructional Steel Research, vol. 191, p. 107189, 2022.

X.-T. Wang and C.-D. Xie, “Experimental and numerical investigation of steel beam-to-CFST column frame-thin steel plate shear walls with cross stiffness,” International Journal of Steel Structures, vol. 19, no. 6, pp. 1895–1910, 2019, doi: 10.1007/s13296-019-00253-z.

Q.-Y. Qiao, W.-L. Cao, X.-Y. Li, H.-Y. Dong, W.-W. Zhang, and F. Yin, “Seismic behavior of shear walls with boundary CFST columns and embedded multiple steel plates: Experimental investigation,” Engineering Structures, vol. 160, pp. 243–256, 2018, doi: 10.1016/j.engstruct.2018.01.040.

X. Liao, X. Li, W. Li, R. Su, and M. Chen, “Seismic behavior of CFST components for shear walls using double corrugated steel plates,” Engineering Structures, vol. 334, p. 120235, 2025, doi: 10.1016/j.engstruct.2025.120235.

Y. Hu, J. Zhao, D. Zhang, and Y. Li, “Cyclic performance of concrete-filled double-skin steel tube frames strengthened with beam-only-connected composite steel plate shear walls,” Journal of Building Engineering, vol. 31, p. 101376, 2020, doi: 10.1016/j.jobe.2020.101376.

K. Wang et al., “Lateral behaviour and failure modes of buckling-restrained beam-only-connected steel plate shear walls,” Engineering Failure Analysis, vol. 142, p. 106833, 2022.

J.-Z. Tong and Y.-L. Guo, “Shear resistance of stiffened steel corrugated shear walls,” Thin-Walled Structures, vol. 127, pp. 76–89, 2018, doi: 10.1016/j.tws.2018.01.036.

J.-Z. Tong, Y.-L. Guo, J.-Q. Zuo, and J.-K. Gao, “Experimental and numerical study on shear resistant behavior of double-corrugated-plate shear walls,” Thin-Walled Structures, vol. 147, p. 106485, 2020, doi: 10.1016/j.tws.2019.106485.

S. Ghodratian-Kashan and S. Maleki, “Experimental investigation of double corrugated steel plate shear walls,” Journal of Constructional Steel Research, vol. 190, p. 107138, 2022, doi: 10.1016/j.jcsr.2022.107138.

L. Feng, H. Yang, T. Sun, and J. Ou, “Experimental and numerical studies on cyclic behavior of stiffened corrugated steel plate shear walls with different corrugation orientations,” Earthquake Engineering & Structural Dynamics, vol. 53, no. 8, pp. 2511–2531, 2024, doi: 10.1002/eqe.4123.

S. Jin, Q. Wang, J. Zhou, and J. Bai, “Experimental and numerical investigation of assembled multi-grid corrugated steel plate shear walls,” Engineering Structures, vol. 251, p. 113544, 2022, doi: 10.1016/j.engstruct.2021.113544.

B. Hao, “Cyclic test vertically corrugated steel plate shear walls with various openings,” Master’s thesis, Tianjin University, Tianjin, China, 2018.

ACI Committee, “Building code requirements for structural concrete (ACI 318-05) and commentary (ACI 318R-05),” American Concrete Institute, Technical Report, 2005.

J.-K. Tan, Y.-H. Wang, M.-N. Su, H.-B. Zhang, and Y.-Y. Peng, “Compressive behaviour of built-up hot-rolled steel hollow and composite sections,” Engineering Structures, vol. 198, p. 109528, 2019.

L.-H. Han, Theory of Concrete-Filled Steel Tubular Structures. Springer, 2024.

P. Lv, “Cyclic behavior of two-layer flat-CSSWs with square opening,” International Journal of Steel Structures, pp. 1–18, 2025, doi: 10.1007/s13296-025-00958-4.

S. Zhang, “Improving the structural performance of steel shear wall systems with four-layer flat-corrugated steel plates in construction engineering,” International Journal of Mechanics and Materials in Design, pp. 1–15, 2025.

X. Liu, “Investigation of the lateral performance of four-layer flat-corrugated steel shear walls under cyclic loading,” Sādhanā, vol. 50, no. 2, p. 81, 2025, doi: 10.1007/s12046-025-02726-w.

J.-Z. Tong, R.-M. Wu, Z.-Y. Xu, and Y.-L. Guo, “Subassemblage tests on seismic behavior of double-corrugated-plate shear walls,” Engineering Structures, vol. 276, p. 115341, 2023, doi: 10.1016/j.engstruct.2022.115341.

R. Deng et al., “Buckling and ultimate resistance of double-corrugated steel plates under in-plane shear load,” Structures, vol. 53, pp. 1267–1282, 2023.

R. Deng, J.-D. Yang, Y.-H. Wang, Q.-Q. Li, and J.-K. Tan, “Cyclic shear performance of built-up double-corrugated steel plate shear walls: Experiment and simulation,” Thin-Walled Structures, vol. 181, p. 110077, 2022, doi: 10.1016/j.tws.2022.110077.

J.-K. Tan et al., “Finite element modelling and design of steel plate shear wall buckling-restrained by hat-section cold-formed steel members,” Journal of Constructional Steel Research, vol. 174, p. 106274, 2020, doi: 10.1016/j.jcsr.2020.106274.

J.-G. Yu, X.-T. Feng, B. Li, and J.-P. Hao, “Cyclic performance of cross restrained steel plate shear walls with transverse braces,” Thin-Walled Structures, vol. 132, pp. 250–264, 2018.

Downloads

Published

2026-11-16

How to Cite

Jiang, H. ., Ji, D. ., & Wang, X. . (2026). Improving the Lateral-Resistant Behavior of Steel Plate Shear Walls with CFST Columns Using Two-Layer Flat-Corrugated Plates. European Journal of Computational Mechanics, 35(03), 145–166. https://doi.org/10.13052/ejcm2642-2085.3531

Issue

Section

Original Article