A Band Stop to Band Pass Filter Transformation Utilizing 3-D Printing Technique for C-band Applications

作者

  • Wael A. E. Ali Department of Electronics & Communications Engineering, College of Engineering and Technology, Arab Academy for Science, Technology and Maritime Transport (AASTMT), Alexandria, Egypt
  • Ahmed A. Ibrahim Electronic Engineering Department, Minia University, El-Minia, Egypt
  • Ashraf E. Ahmed Electronics & Comm. Engineering Department, College of Engineering, Higher Institute of Engineering and Technology, King Marriott, Alexandria, Egypt

##plugins.pubIds.doi.readerDisplayName##:

https://doi.org/10.13052/2022.ACES.J.371105

关键词:

3-D printing, bandpass filter, C-band applications, PLA

摘要

In this paper, a band-pass filter (BPF) based on split-ring resonator (SRR) using a 3-D printing technique for C-band applications is introduced. The proposed filter is designed to operate at a frequency of 3.9 GHz. An innovative technique for printing the substrate with a size of 24 x 24 x 1.1 mm3 using PLA dielectric material is implemented. The copper sheet with a thickness of 0.1 mm is printed on the upper and lower faces of the substrate. First, the SRR band stop filter (BSF) is introduced then two L-Stubs are inserted to implement an additional band stop region, and this rejoin is adjusted to obtain a band-pass region between the two stopbands. The BPF is operated at a 3-dB bandwidth extended from 3.5 GHz to 4.3 GHz with an S21 level of -0.2 dB for the simulated results while it achieves a 3-dB bandwidth within 3.6 GHz to 4.2 GHz (15.3 %) with an S21 level of -1.8 dB for the measured results.

##plugins.generic.usageStats.downloads##

##plugins.generic.usageStats.noStats##

##submission.authorBiographies##

##submission.authorWithAffiliation##

Wael A. E. Ali was born in 1982. He received his B.Sc. and M.Sc. in Electronics and Communications Engineering from the Arab Academy for Science, Technology and Maritime Transport (AASTMT), Alexandria, Egypt in 2004 & 2007, respectively. He received his Ph.D. in Electronics and Communications Engineering from Alexandria University, Alexandria, Egypt in 2012. He is now a Professor of Electronics and Communications Engineering, as well as the Head of the Quality Assurance unit in the College of Engineering and Technology.

##submission.authorWithAffiliation##

Ahmed A. Ibrahim was born in 1986. He received his B.Sc. degree, M.Sc., and Ph.D. in Electrical Engineering from the Electronic and Communication Engineering Department, Minia University, Elminia, Egypt in 2007, 2011, and 2014 respectively. He is now an Associated Professor at the Electrical Engineering Department in the Faculty of Engineering, Minia University.

##submission.authorWithAffiliation##

Ashraf E. Ahmed is currently a lecturer at the Electronics and Communications Engineering Department, Higher Engineering and Technology, King Marriott Academy (KMA), Alexandria, Egypt. He received his B.Sc. and M.Sc. degrees in Electronics and Communication Engineering from the Faculty of Engineering, Alexandria University, Egypt.

参考

L. Zhou, Y. Z. Yin, W. Hu, and X. Yang, “Compact bandpass filter with sharp out-of-band rejection and its application,” Applied Computational Electromagnetics Society (ACES) Journal, vol. 32, no. 3, pp. 249-255, 2017.

A. Rajput, K. Patel, and A. Birwal, “Compact microstrip low pass filter design using U-shaped folded high-impedance line,” Microwave and Optical Technology Letters, vol. 60, no. 7, pp. 1812-1815, 2018.

A. A. Ibrahim, M. A. Abdalla, and W. A. E. Ali, “Small size and wide-band band pass filter with DGS/CRLH structures,” Applied Computational Electromagnetics Society (ACES) Journal, vol. 34, no. 5, pp. 777-783, 2019.

Z. Zhu, L. Cao, and C. Wei, “Novel compact microstrip dual-mode filters with two controllable transmission zeros,” Applied Computational Electromagnetics Society Journal (ACES), vol. 33, no.1, pp. 43-48, 2018.

A. Sami, M. Rahman, H. Ahmad, and S. Bashir, “Design strategy for compact bandpass filters using meander line resonators,” Applied Computational Electromagnetics Society (ACES) Journal, vol. 35, no. 1, pp. 44-50, 2020.

A. A. Ibrahim, H. A. Mohamed, and W. A. E. Ali, “Tunable dual/triple band-pass filter based on stub-loaded resonators for wireless applications,” Journal of Instrumentation, vol. 12, pp. 1-12, 2017.

A. A. Ibrahim, W. A. E. Ali, and M. A. Abdelghany, “Design of dual-band dual-mode band-pass filter utilizing 0∘

feed structure and lumped capacitors for WLAN/WiMAX applications,” Electronics, vol. 9, no. 10, pp. 1697, 2021.

A. Boutejdar, A. A. Ibrahim, and W. A. E. Ali, “Design of compact size and tunable band pass filter for WLAN applications,” Electronics Letters, vol. 52, no. 24, pp. 1996-1997, 2016.

Z. Yang, B. You, and G. Luo. “Dual−

/tri-band bandpass filter using multimode rectangular SIW cavity,” Microwave and Optical Technology Letters, vol. 62, no. 3, pp. 1098-1102, 2020.

K. A. Ansal, D. S. Jose, A. S. Kumar, and T. Shanmugantham, “A band pass coupled line filter with DGS for ultra-wide band application,” Procedia Computer Science, vol. 171, pp. 561-567, 2020.

J. Chen, J. Zhong, J. Shen, N. Gao, and A. Zhang, “Design of compact tri-band filter based on sir-loaded resonator with 0∘

tapped-feed structure,” Frequenz, vol. 69, no. 9-10, pp. 389-392, 2015.

A. A. Ibrahim, M. A. Abdalla, and W. A. E. Ali, “Dual band pass filter with sharp transmission zeros for wireless applications,” Journal of Instrumentation, vol. 13, no. 6, P06020, 2018.

L. Zhao, Y. Li, Z. M. Chen, X.H. Liang, J. Wang, X. Shen, and Q. Zhang, “A band-pass filter based on half-mode substrate integrated waveguide and spoof surface plasmon polaritons,” Scientific Reports, vol. 9, no. 1, pp.1-8, 2019.

M. Amzi, S. D. Bennani, J. Zbitou, and A. Belmajdoub, “Design of compact bandpass filter based on SRR and CSRR for 5G applications,” International Conference on Electronic Engineering and Renewable Energy, Springer, Singapore, pp. 175-181, 2020.

G. Carranza, U. Robles, C. L. Valle, J. J. Gutierrez, and R. C. Rumpf, “Design and hybrid additive manufacturing of 3D/volumetric electrical circuits,” IEEE Trans. on Components, Packaging, and Manufacturing Technology, vol. 9, no. 6, pp. 1176-1183, 2019.

A. E. Ahmed, W. A. E. Ali, A. Chowdhury, and S. Das, “A 3-D printed trapezoidal antenna for X-band wireless communications applications,” Futuristic Communication and Network Technologies, Springer, Singapore, pp. 949-956, 2022.

A. E. Ahmed and W. A. E. Ali, “Analysis and design of 3-D printed fractal triangular antenna for wireless communications applications.” International Conference on Electrical, Communication, and Computer Engineering (ICECCE), pp. 1-5, 2020.

A. E. Ahmed, W. A. E. Ali, and S. Das, “Quintuple band circular monopole antenna with innovative3-D printed PLA substrate for wireless applications,” Frequenz, vol. 76, no. 3-4, pp. 199-207, 2022.

A. E. Ahmed, W. A. E. Ali, and S. Das, “A 3D printed 2x2 circular planar antenna array for wireless communications applications,” Journal of Nano-and Electronic Physics, vol. 13, no. 3, pp. 03028-1-03028-4, 2021.

I. O. Saracho-Pantoja, J. R. Montejo-Garai, J. A. Ruiz-Cruz, and J. M. Rebollar, “Additive manufacturing of 3D printed microwave passive components,” Emerging Microwave Technologies in Industrial, Agricultural, Medical and Food Processing, p. 93, 2018.

U. Robles, E. Bustamante, P. Darshni, and R. C. Rumpf, “High-frequency filters manufactured using hybrid 3D printing method,” Progress In Electromagnetics Research M, vol. 84, pp. 147-155, 2019.

B. Zhang and H. Zirath, “3D printed iris bandpass filters for millimetre-wave applications,” Electronics Letters, vol. 51, no. 22, pp. 1791-1793, 2015.

T. A. Sheikh, J. Borah, and S. Roy. “Design of compact bandpass filter for WiMAX and UWB application using asymmetric SIRs and DGS,” Radioelectronics and Communications Systems, vol. 59, no. 6, pp. 269-273, 2016.

T. Firmansyah, M. Alaydrus, Y. Wahyu, E. T. Rahardjo, and G. Wibisono, “A highly independent multiband bandpass filter using a multi-coupled line Stub-SIR With folding structure,” IEEE Access, vol. 8, pp. 83009-83026, 2020.

##submission.downloads##

已出版

2022-11-30

##submission.howToCite##

[1]
W. A. E. . Ali, A. A. . Ibrahim, 和 A. E. . Ahmed, 《A Band Stop to Band Pass Filter Transformation Utilizing 3-D Printing Technique for C-band Applications》, ACES Journal, 卷 37, 期 11, 页 1146–1152, 11月 2022.

期

2022: Vol 37 Iss 11

栏目

General Submission

##category.category##