Design and Finite Element Analysis of a Novel Permanent Magnet Assisted Reluctance Synchronous Motor
关键词:
Asymmetric flux barriers, Finite Element Analysis (FEA), magnet width, PMASRM, torque ripple摘要
In this paper, a permanent magnet assisted synchronous reluctance machine (PMASRM) with optimized permanent magnet width and asymmetric rotor structure is proposed. A typical PMASRM is selected as the reference motor (Pre-optimized PMASRM). In order to reduce the large torque ripple of conventional PMASRM, an optimization method to design the permanent magnet width is investigated and the Optimized Magnet-width PMASRM is proposed. On this basis, an asymmetric flux barriers structure is proposed to further reduce the torque ripple. Some electromagnetic characteristics including air-gap flux density, no-load back EMF and motor efficiency are examined by Finite Element Analysis (FEA). The simulation results show that the proposed PMASRM can not only decrease the harmonic component of no-load back EMF obviously, but also reduce the torque ripple in steady-state operation, which proves the rationality of the motor structure.
##plugins.generic.usageStats.downloads##
参考
M. De Gennaro, J. Jürgens, A. Zanon, J. Gragger, E. Schlemmer, A. Fricassè, L. Marengo, B. Ponick, E. T. Olabarri, J. Kinder, A. Cavallini, P. Mancinelli, M. Hernandez, and M. Messagie, "Designing, prototyping and testing of a ferrite permanent magnet assisted synchronous reluctance machine for hybrid and electric vehicles applications," Sustainable Energy Technologies & Assessments, vol. 31, pp. 86-101, Jan. 2019.
J. X. Shen, "Analysis and design of synchronous reluctance machines PART I: An overview," Microwaves, vol. 44, no. 10, pp. 72-79, Oct. 2016.
X. Liu, Y. Li, Z. Liu, T. Ling, and Z. Luo, "Optimized design of a high-power-density PMassisted synchronous reluctance machine with ferrite magnets for electric vehicles," Archives of Electrical Engineering, vol. 66, no. 2, pp. 279-293, 2017.
K. Wang, Z. Q. Zhu, G. Ombach, M. Koch, S. Zhang, and J. Xu, "Torque ripple reduction of synchronous reluctance machines: using asymmetric flux-barrier", COMPEL - The International Journal for Computation and Mathematics in Electrical and Electronic Engineering, vol. 34, no. 1, pp. 18-31, Jan. 2015.
T. Mohanarajah, J. Rizk, A. Hellany, M. Nagrial and A. Klyavlin, "Torque ripple improvement in synchronous reluctance machines," 2018 2nd International Conference on Electrical Engineering (EECon), Colombo, pp. 44-50, Sept. 2018.
M. Sanada, K. Hiramoto, S. Morimoto, and Y. Takeda, "Torque ripple improvement for synchronous reluctance motor using an asymmetric flux barrier arrangement," 38th IAS Annual Meeting on Conference Record of the Industry Applications Conference, vol. 1, pp. 250-255, Oct. 2003.
M. Davoli, C. Bianchini, A. Torreggiani, and F. Immovilli, "A design method to reduce pulsating torque in PM assisted synchronous reluctance machines with asymmetry of rotor barriers," 2016 42nd Annual Conference of the IEEE Industrial Electronics Society (IECON), pp. 1566-1571, Oct. 2016.
M. Xu, G. Liu, and Q. Chen, "Torque ripple improvement for ferrite-assisted synchronous reluctance motor by using asymmetric flux-barrier arrangement," International Journal of Applied Electromagnetics & Mechanics, pp. 1-10, 2019.
N. Bianchi, E. Fornasiero, and W. Soong, "Selection of PM flux linkage for maximum lowspeed torque rating in a PM-assisted synchronous 1020 ACES JOURNAL, Vol. 35, No. 9, September 2020 reluctance machine," IEEE Transactions on Industry Applications, vol. 51, no. 5, pp. 3600-3608, 2015.
N. Bianchi, S. Bolognani, D. Bon, and M. Dai Pre, "Rotor flux-barrier design for torque ripple reduction in synchronous reluctance and PMassisted synchronous reluctance motors," IEEE Transactions on Industry Applications, vol. 45, no. 3, pp. 921-928, 2009.
N. Bianchi, S. Bolognani, D. Bon, and M. Dai PrÉ, "Torque harmonic compensation in a synchronous reluctance motor," IEEE Transactions on Energy Conversion, vol. 23, no. 2, pp. 466-473, June 2008.
H. Cai, B. Guan, and L. Xu, "Low-cost ferrite PM-assisted synchronous reluctance machine for electric vehicles," IEEE Transactions on Industrial Electronics, vol. 61, no. 10, pp. 5741-5748, Oct. 2014.
F. Xing, W. Zhao, and B. Kwon, "Design of a novel rotor structure for PM-assisted synchronous reluctance machines to improve torque characteristics," 2016 IEEE Conference on Electromagnetic Field Computation (CEFC), Miami, FL, pp. 1-1, 2016.
R. Rouhani, S. E. Abdollahi, and S. A. Gholamian, "Torque ripple reduction of a synchronous reluctance motor for electric vehicle applications," 2018 9th Annual Power Electronics, Drives Systems and Technologies Conference (PEDSTC), Tehran, pp. 386-391, 2018.
B. Boazzo, A. Vagati, G. Pellegrino, E. Armando, and P. Guglielmi, "Multipolar ferrite-assisted synchronous reluctance machines: A general design approach," IEEE Transactions on Industrial Electronics, vol. 62, no. 2, pp. 832-845, Feb. 2015.
X. Zhang, L. Zeng, and R. Pei, "Designing and comparison of permanent magnet synchronous reluctance motors and conventional motors in electric vehicles," 2018 21st International Conference on Electrical Machines and Systems (ICEMS), Jeju, pp. 202-205, 2018.
R. T. Ugale and B. N. Chaudhari, "A new rotor structure for line start permanent magnet synchronous motor," 2013 International Electric Machines & Drives Conference, Chicago, IL, pp. 1436-1442, 2013.
H. Huang, Y. Hu, Y. Xiao, and H. Lyu, "Research of parameters and anti-demagnetization of rareearth-less permanent magnet assisted synchronous reluctance motor," 2015 IEEE International Magnetics Conference (INTERMAG), Beijing, pp. 1-1, 2015.
N. Bianchi and M. Barcaro, "Iron losses reduction in synchronous motors with anisotropic rotor," 2008 34th Annual Conference of IEEE Industrial Electronics, Orlando, FL, pp. 1258-1263, 2008.