Mechanism and Performance Analysis of the Pilot-Pressure Control Two-Stage Valve Distribution High Pressure Radial Piston Hydraulic Motor

Authors

  • Tong Guo Huaqiao University, Xiamen, Fujian, China; Fujian Key Laboratory of Green Intelligent Drive and Transmission for Mobile Machinery, Xiamen, Fujian, China https://orcid.org/0000-0002-6589-9999
  • Fumin Que Huaqiao University, Xiamen, Fujian, China; Fujian Key Laboratory of Green Intelligent Drive and Transmission for Mobile Machinery, Xiamen, Fujian, China
  • Xinming Li Huaqiao University, Xiamen, Fujian, China; Fujian Key Laboratory of Green Intelligent Drive and Transmission for Mobile Machinery, Xiamen, Fujian, China
  • Hao Liu Beijing Tianma Intelligent Control Technology Co., Ltd., Beijing, 100176, China
  • Tianliang Lin Huaqiao University, Xiamen, Fujian, China; Fujian Key Laboratory of Green Intelligent Drive and Transmission for Mobile Machinery, Xiamen, Fujian, China

DOI:

https://doi.org/10.13052/ijfp1439-9776.2732

Keywords:

Hydraulic motor, Pilot-pressure control two-stage flow distribution, Radial piston, Volumetric efficiency, valve distribution

Abstract

Radial piston motors are typical high-torque rotary actuators with good low-speed stability, high power density and cost efficiency, which are widely used in the field of heavy-duty machinery. The rated pressure of mainstream radial piston motors does not exceed 25 MPa due to the inherent limitations of their conventional flow distribution mechanisms. To address this issue, a new distribution scheme of pilot-pressure control two-stage flow distribution is proposed, in which the pilot-stage valve plate controls conical valve pairs serving as the main-stage distributors of the motor. Specifically, the study focuses on the mechanical principle and hydraulic performance of the pilot-pressure control flow distribution system, systematically analyzing the influence of two different configurations on motor output characteristics and further confirming the feasibility through simulation and experimental validation. This approach leverages the pilot ratio of the distribution valve to significantly reduce the pressure acting on the distribution pair, thereby achieving a substantial improvement in volumetric efficiency under high-pressure conditions and providing both theoretical innovation and practical engineering reference for the development of high-performance hydraulic motors.

Downloads

Download data is not yet available.

Author Biographies

Tong Guo, Huaqiao University, Xiamen, Fujian, China; Fujian Key Laboratory of Green Intelligent Drive and Transmission for Mobile Machinery, Xiamen, Fujian, China

Tong Guo received his Ph.D. degree in Mechanical Engineering from Xi’an Jiaotong University in 2016. From 2016 to 2019, he worked at the Research Institute of Petroleum Exploration and Development (RIPED), PetroChina, where he was engaged in research on oil production engineering technologies. He later joined Huaqiao University, where he is currently an Associate Professor at the College of Mechanical Engineering and Automation. His research interests include high-performance hydraulic components, hydrodynamic and electro-hydraulic transmission systems, energy-saving technologies, and downhole flow control techniques for oilfield development.

Fumin Que, Huaqiao University, Xiamen, Fujian, China; Fujian Key Laboratory of Green Intelligent Drive and Transmission for Mobile Machinery, Xiamen, Fujian, China

Fumin Que received the B.E. degree in the mechanical engineering from Huaqiao University in 2023. He is currently pursuing the M.S. degree with the College of Mechanical Engineering and Automation, Huaqiao University. His research encompasses high-performance hydraulic components including motors, flowmeters, and pumps.

Xinming Li, Huaqiao University, Xiamen, Fujian, China; Fujian Key Laboratory of Green Intelligent Drive and Transmission for Mobile Machinery, Xiamen, Fujian, China

Xinming Li received the B.E. degree in the mechanical engineering from Huaqiao University in 2024. He is currently pursuing the M.S. degree with the College of Mechanical Engineering and Automation, Huaqiao University. His research interests include high-performance hydraulic component, control of hydrodynamic and electro-hydraulic transmission systems.

Hao Liu, Beijing Tianma Intelligent Control Technology Co., Ltd., Beijing, 100176, China

Hao Liu received his Master’s degree in Mechanical Engineering from Harbin Institute of Technology in 2013. From 2013 to now, he worked at Beijing Tianma Intelligent Control Technology Co., Ltd., where he was engaged in research on Mining machinery and equipment.

Tianliang Lin, Huaqiao University, Xiamen, Fujian, China; Fujian Key Laboratory of Green Intelligent Drive and Transmission for Mobile Machinery, Xiamen, Fujian, China

Tianliang Lin received his B.E. degree from Fuzhou University in 2006 and his Ph.D. degree in Fluid Power Transmission and Control from Zhejiang University in 2011. He is currently a Professor and Doctoral Supervisor at the College of Mechanical Engineering and Automation, Huaqiao University, where he also serves as the Dean. His research interests include electro-hydraulic control, intelligentization of construction machinery, and energy-saving technologies.

References

Y. Li, R&D of China’s strategic new industries [M]. Beijing: High-end hydraulic pneumatic and sealing components, 2021.

S. Sakama, Y. Tanaka, A. Kamimura, ‘Characteristics of Hydraulic and Electric Servo Motors,’ Actuators J., vol. 11, no. 1, pp. 11, 2022.

J. Pustavrh, M. Hočevar, P. Podržaj, et al., ‘Comparison of hydraulic, pneumatic and electric linear actuation systems,’ Scientific Reports J., vol. 13, no. 1, pp. 20938, 2023.

T. Kazama, ‘Comparison of power density of transmission elements in hydraulic, pneumatic, and electric drive systems,’ Mechanical Engineering Letters J., vol. 5, pp. 19-00139, 2019.

Parker Hannifin Corp. Radial Piston Motors [EB/OL]. [2023-01-10]. https://ph.parker.com/us/en/radial-piston-motors.

Kawasaki Motors Corp.Staffa Motor [EB/OL]. [2023-01-07]. http://www.kpm-usa.com/wp-content/uploads.

Intra-Italy Corp. Low-speed high-torque hydraulic motor [EB/OL]. http://www.intra-italy.com.

H. Ma, W. Liu, D. Wu, et al., ‘Modeling and analysis of the leakage performance of the spherical valve plate pair in axial piston pumps,’ Engineering Science and Technology, an International Journal J., vol. 45, pp. 101498, 2023.

Y. Chen, C. Hua, C. Tong, et al., ‘Volumetric efficiency in motor-driven two-dimensional piston pumps with leakage and reverse flow under high pressure,’ Scientific Reports J., vol. 14, no. 1, pp. 28963, 2024.

B. Xu, M. Hu, J. Zhang, et al., ‘Characteristics of volumetric losses and efficiency of axial piston pump with respect to displacement conditions,’ Journal of Zhejiang University – Science A J., vol. 17, no. 3, pp. 186–201, 2016.

W. Yin, J. Zhang, X. Wang, et al., ‘Volumetric efficiency degradation prediction of axial piston pump based on friction and wear test,’ Heliyon J., vol. 10, no. 17, pp. 2024.

L. Li, J. Chen, L. Gu, et al., ‘Variable displacement distributor with valve control for axial piston pump/motor,’ Journal of Zhejiang University:Engineering Science J., vol. 48, no. 1, pp. 29–34, 2014.

K. Pate, I. Azzam, F. Breidi, et al., ‘Digitalization of Radial Piston Pumps through Internal Mechanically Actuated Designs,’ J., vol. 12, no. 11, pp. 425, 2023.

Imenco. Imenco Bauer and Diinef Digital Motor [EB/OL]. [2025-01-26]. https://imenco.no/imenco-bauer-hydraulics-and-diinef-launch-digital-motor.

J. Man, J. Zhao, Y. Wang, et al., ‘Working Characteristics of Crankshaft Swing Cylinder Water Hydraulic Motor with Flow Distribution Valve,’ Transactions of the Chinese Society for Agricultural Machinery J., vol. 54, no. 1, pp. 450–458, 2023.

T. Guo, T. Lin, H. Ren, et al., ‘Modeling and theoretical study of relief chamfer method for reducing the flow ripple of a spool valves distribution radial piston pump,’ J., vol. 235, no. 19, pp. 3819–3832, 2021.

Danfoss. Digital Displacement Pumps and Motors [EB/OL]. [2023-01-26]. https://www.danfoss.com.

W. Shen, S. Nie, F. Yin, et al., ‘Structure Design and Simulation Analysis of a New Type Low-speed Large-torque Water Hydraulic Motor,’ Hydraulics & Pneumatics J., no. 06, pp. 17–21, 2019.

N. Xu, J. Wang, W. Min, et al., ‘The Effect of Piston Pump Spherical Valve Plate Triangular Groove Flow Area on Outlet Flow Pulsation,’ Hydraulics & Pneumatics J., vol. 42, no. 04, pp. 19–24, 2022.

Y. Chen, J. Zhang, B. Xu, ‘Multi-objective optimization of micron-scale surface textures for the cylinder/valve plate interface in axial piston pumps,’ Tribology International J., vol. 138, pp. 316–329, 2019.

L. Kumar, N. P. Mandal, ‘Effect of valve plate silencing grooves on flow and pressure fluctuation in fixed displacement radial piston pump,’ Journal of Computational & Applied Research in Mechanical Engineering J., vol. 13, no. 1, pp. 55–66, 2023.

G. K. Seeniraj, M. Ivantysynova, Impact of Valve Plate Design on Noise, Volumetric Efficiency and Control Effort in an Axial Piston Pump; proceedings of the ASME 2006 International Mechanical Engineering Congress and Exposition, F, 2006 [C].

D. Richardson, F. Sadeghi, R. G. Rateick, ‘Dynamic Modeling of Floating Valve Plate Motion in an Axial Piston Pump,’ Tribology Transactions J., vol. 61, no. 4, pp. 683–693, 2018.

D. Gao, H. Ma, J. Liu, et al., ‘Numerical Simulation on Loading Characteristics of Port Plate Pair with Non-smooth Surface for Water Hydraulic Motor,’ Hydraulics & Pneumatics J., no. 11, pp. 61–69, 2018.

H. Ma, D. Gao, S. Wu, et al., ‘Experimental Study on Friction-wear for Valve Plate with Bionic Non-smooth Surface of Hydraulic Motor,’ Journal of Mechanical Engineering J., vol. 54, no. 13, pp. 142–152, 2018.

S. Nie, Z. Wan, W. Liu, ‘Theoretical Research of A New Type Valve Plate,’ Machine Tool & Hydraulics J., no. 03, pp. 88–90, 2004.

J. M. Bergada, J. Watton, S. Kumar, ‘Pressure, Flow, Force, and Torque Between the Barrel and Port Plate in an Axial Piston Pump,’ Journal of Dynamic Systems Measurement and Control J., vol. 130, pp. 2018.

T. Guo, T. Luo, T. Lin, Radial piston hydraulic device distributing flow by pilot operated check valves and operating method thereof, US12129874B2 [P]. [2024-10-29].

J. Zhao, L. Liu, ‘Influence of reversing impact load on performance of a two-step unloading pilot-operated check valves,’ Journal of the Brazilian Society of Mechanical Sciences and Engineering J., vol. 40, no. 6, pp. 295, 2018.

Y. Yin, D. Wang, J. Fu, et al., ‘Effect of Dynamic Pressure Feedback Orifice on Stability of Cartridge-Type Hydraulic Pilot-Operated Relief Valve,’ Chinese Journal of Mechanical Engineering J., vol. 36, no. 1, pp. 85, 2023.

W. Wei, H. Jian, Q. Yan, et al., ‘Nonlinear modeling and stability analysis of a pilot-operated valve-control hydraulic system,’ J., vol. 10, no. 11, pp. 1687814018810660, 2018.

T. Guo, T. Luo, T. Lin, Radial piston hydraulic device distributed by pilot operated check valves, US11781537B2 [P]. [2023-10-10].

Downloads

Published

2026-11-16

How to Cite

Guo, T. ., Que, F. ., Li, . X. ., Liu, H. ., & Lin, T. . (2026). Mechanism and Performance Analysis of the Pilot-Pressure Control Two-Stage Valve Distribution High Pressure Radial Piston Hydraulic Motor. International Journal of Fluid Power, 27(03), 511–538. https://doi.org/10.13052/ijfp1439-9776.2732

Issue

Section

Original Article

Most read articles by the same author(s)