Hydraulic Hybrid Solution for Peak Power Reduction in Electrified Mobile Machine

Authors

  • Mikko Huova Tampere University, Automation Technology and Mechanical Engineering Korkeakoulunkatu 6, 33720 Tampere, Finland https://orcid.org/0000-0001-6384-7688

DOI:

https://doi.org/10.13052/ijfp1439-9776.2737

Keywords:

Mobile machine, Wheel loader, Hydraulic hybrid, Electrification, Digital hydraulics

Abstract

Enhancing the energy efficiency of mobile machines is essential for advancing sustainable off-road equipment. Electrification can lead to decreased power losses and local emissions produced. However, full electrification of a mobile machine requires typically a number of high-power electric drives, increasing the manufacturing cost of the machine. This study explores a hydraulic hybrid system implemented on an electrified wheel loader, combining digital hydraulics with a hydraulic accumulator to enable fast dynamics and precise control. Single-accumulator and double-accumulator configurations are compared and discussed. A simulation model making use of measured real-world load cycle data is created to study the potential. The results indicate significant potential to downsize the electric drive. The study provides insights into the integration of hydraulic energy storage and control technologies in next-generation mobile machinery.

Downloads

Download data is not yet available.

Author Biography

Mikko Huova, Tampere University, Automation Technology and Mechanical Engineering Korkeakoulunkatu 6, 33720 Tampere, Finland

Mikko Huova received his MSc in automation engineering in 2008 and completed his PhD in the same field in 2015, both from Tampere University of Technology. He is currently working as a senior research fellow at the Automation Technology and Mechanical Engineering unit at Tampere University. His areas of interest include energy efficient actuator systems, mobile machinery and model-based control.

References

A. Jansson and J. Palmberg, “Separate Controls of Meter-in and Meter-out Orifices in Mobile Hydraulic Systems,” SAE Technical Paper 901583, 1990.

A. Shenouda, “Quasi-Static Hydraulic Control Systems and Energy Savings Potential Using Independent Metering Four-Valve Assembly Configuration,” Ph.D. dissertation, Woodruff School of Mechanical Engineering, Georgia Institute of Technology, 2006.

M. Linjama, M. Huova, P. Boström, et al., “Design and implementation of energy saving digital hydraulic control system,” in The Tenth Scandinavian International Conference on Fluid Power, Tampere, Finland, May 21–23, 2007.

K. Abuowda, I. Okhotnikov, S. Noroozi, et al., “A review of electrohydraulic independent metering technology,” ISA Transactions, vol. 98, pp. 364–381, 2020.

X. Liu, “A Review of Potential Energy Recovery and Reutilization Technologies for Hydraulic-Driven Manipulators in Construction Machinery,” International Journal of Mechatronics and Applied Mechanics, 2025, no. 20, vol. 1.

T. Jung, H. Raduenz, P. Krus, V. De Negri, and J. Lee, “Boom energy recuperation system and control strategy for hydraulic hybrid excavators,” Automation in Construction, vol. 135, p. 104046, 2022.

P. Casoli, L. Riccò, F. Campanini, and A. Bedotti, “Hydraulic Hybrid Excavator – Mathematical Model Validation and Energy Analysis,” Energies, vol. 9, no. 12, p. 1002, 2016, doi: 10.3390/en9121002.

M. Vukovic, R. Leifeld, and H. Murrenhoff, “STEAM – a hydraulic hybrid architecture for excavators,” in 10th International Fluid Power Conference, Dresden, Germany, 2016.

R. Hippalgaonkar and M. Ivantysynova, “Optimal power management of hydraulic hybrid mobile machines – Part I: Theoretical studies, modeling and simulation,” Journal of Dynamic Systems, Measurement, and Control, vol. 138, no. 5, p. 051002, 2016.

R. Hippalgaonkar and M. Ivantysynova, “Optimal power management of hydraulic hybrid mobile machines – Part II: Machine implementation and measurements,” Journal of Dynamic Systems, Measurement, and Control, vol. 138, no. 5, p. 051003, 2016.

K. Einola and A. Kivi, “Hydraulic hybrid cut-to-length forest harvester – evaluation of effects on Productivity and Fuel Efficiency,” in Actuators, vol. 13, no. 4, p. 126, MDPI, 2024.

M. Linjama, M. Huova, J. Tammisto, et al., “6-ton wheel loader short Y-cycle data for 440 seconds loading of gravel,” Zenodo, dataset, Feb. 9, 2024, doi: 10.5281/zenodo.10639199.

M. Linjama and M. Huova, “Digital Hydraulic Control of Accumulator Flow in Hydraulic Hybrid,” in Workshop on Digital Fluid Power 2024, pp. 164–182, Tampere, Finland, 2024.

M. Huova, “Digital hydraulic work functions of a prototype wheel loader,” in The Twelfth Workshop on Digital Fluid Power, Tampere, Finland, June 6–7, 2024.

A. Ellman and R. Piche, “Modified orifice flow formula for numerical simulation of fluid power systems,” in ASME Fluid Power Systems and Technology (FPST), vol. 3, pp. 59–63, 1996.

M. Huova, J. Tammisto, M. Linjama, et al., “Fuel Efficiency Analysis of Selected Hydraulic Hybrids in a Wheel Loader Application,” in Symposium on Fluid Power and Motion Control (FPMC), Bath, U.K., Sept. 12–14, 2018.

Innas B.V., “Performance of Hydrostatic Machines,” Breda, Netherlands, June 8, 2020. [Online]. Available: https://www.innas.com/assets/performance-of-hydrostatic-machines.pdf, [Accessed: Aug. 14, 2025].

Engiro, “ENGIRO_Datasheet_205W_12023_P_ABC_V002.pdf.” [Online]. Available: https://www.engiro.com/products/motors-and-generators, [Accessed: Aug. 27, 2025].

A. Aroua, W. Lhomme, F. Verbelen, et al., “Impact of scaling laws of permanent magnet synchronous machines on the accuracy of energy consumption computation of electric vehicles,” eTransportation, vol. 18, p. 100269, 2023.

Downloads

Published

2026-11-16

How to Cite

Huova, M. . (2026). Hydraulic Hybrid Solution for Peak Power Reduction in Electrified Mobile Machine. International Journal of Fluid Power, 27(03), 649–649. https://doi.org/10.13052/ijfp1439-9776.2737

Issue

Section

Original Article