Manipulation Strategy of Vortex Cavitation Evolution in Poppet Valves Through Structure Modification

Authors

  • Cong Yuan College of Mechanical and Automotive Engineering, Zhaoqing University, Zhaoqing City, Guangdong Province, People’s Republic of China https://orcid.org/0000-0002-4101-9045

DOI:

https://doi.org/10.13052/ijfp1439-9776.2734

Keywords:

Vortex cavitation, cavitation manipulation, poppet valve, cavitation evolution

Abstract

Owing to the extreme operating conditions experienced by poppet valves, cavitation occurs frequently and unavoidably. This study investigates manipulation strategies for vortex cavitation throughout its evolutionary process within poppet valves featuring a sharp valve seat. The flow dynamics of the cavitating jet are elucidated via a series of numerical simulations. Cavitation is found to occur mainly in three distinct regions: free-shearing vortex cavitation, wall-shearing vortex cavitation, and attached cavitation at the poppet trailing edge. The formation mechanisms of these three cavitation types are further revealed based on the corresponding flow dynamics. The cyclic behavior of cavitation structures identifies two key interactions during the transient evolution of the cavitating jet, which are the merging of free-shearing and wall-shearing vortex cavitation, and the secondary growth of vortex cavitation accompanied by entrainment of attached cavitation. Through detailed analysis of cavitation intensity variations under different valve openings, it is shown that the development of free-shearing vortex cavitation is primarily governed by the intensity and thickness of the shear layer, whereas wall-shearing cavitation is additionally influenced by the jet potential core thickness, and attached cavitation is controlled by the local velocity gradient. Guided by the identified cavitation dynamics mechanisms, manipulation strategies through structural modification are proposed to suppress the developmental growth of each cavitation form. Finally, a complementary numerical investigation validates the effectiveness of the proposed manipulation strategies and the modified geometry in mitigating overall cavitation intensity.

Downloads

Download data is not yet available.

Author Biography

Cong Yuan, College of Mechanical and Automotive Engineering, Zhaoqing University, Zhaoqing City, Guangdong Province, People’s Republic of China

Cong Yuan received B.E., M.E., and Ph.D. degrees in mechanical engineering from Northeastern University, Shenyang, China, in 2019. He is currently an associate professor with the School of Mechanical and Automotive Engineering, Zhaoqing University, Zhaoqing, China. His main research interests include cavitation in hydraulic valves, cavitating jets, and cavitation erosion.

References

S. Oshima and T. Ichikawa, “Cavitation phenomena and performance of oil hydraulic poppet valve: 1st report – mechanism of generation of cavitation and flow performance,” Bulletin of the JSME, vol. 28, no. 244, pp. 2264–2271, 1985.

S. Oshima and T. Ichikawa, “Cavitation phenomena and performance of oil hydraulic poppet valve: 2nd report – influence of the chamfer length of the seat and the flow performance,” Bulletin of the JSME, vol. 28, no. 244, pp. 2272–2279, 1985.

S. Oshima and T. Ichikawa, “Cavitation phenomena and performance of oil hydraulic poppet valve: 5th report – influence of dimensions of valve on the thrust force characteristics,” Bulletin of the JSME, vol. 29, no. 251, pp. 1427–1433, 1986.

S. Oshima, T. Leino, M. Linjama, K. T. Koskinen, and M. J. Vilenius, “Effect of cavitation in water hydraulic poppet valves,” International Journal of Fluid Power, vol. 2, no. 3, pp. 5–13, 2001.

S. Washio, S. Kikui, and S. Takahashi, “Nucleation and subsequent cavitation in a hydraulic oil poppet valve,” Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, vol. 224, no. 4, pp. 947–958, 2010.

D. Yi, L. Lu, J. Zou, and X. Fu, “Interactions between poppet vibration and cavitation in relief valve,” Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, vol. 229, no. 8, pp. 1447–1461, 2015.

D. M. Cavallo, O. Chiavola, E. Frattini, and F. Palmieri, “A novel approach for hydraulic valve experimental assessment under cavitating condition,” International Journal of Fluid Power, pp. 183–204, 2022.

M. Han, Y. Liu, D. Wu, X. Zhao, and H. Tan, “A numerical investigation in characteristics of flow force under cavitation state inside the water hydraulic poppet valves,” International Journal of Heat and Mass Transfer, vol. 111, pp. 1–16, 2017.

H. Ueno, A. Okajima, and Y. Muromiya, “Visualization of cavitating flow and numerical simulation of flow in a poppet valve,” in Proc. JFPS Int. Symp. on Fluid Power, pp. 385–390, 1993.

C. Yuan, Y. Cai, S. Liu, and Z. Du, “Simulation of cavitating jet through a poppet valve with special emphasis on laminar–turbulent transition,” International Journal of Fluid Power, pp. 27–58, 2020.

C. Yuan, J. Song, and M. Liu, “Coherent structure of paired vortex and transition in flow pattern in cavitating jet through a poppet valve,” International Journal of Mechanical Sciences, vol. 152, pp. 19–33, 2019.

L. Liang, Z. Liang, Y. Liu et al., “Geometrical transition properties of vortex cavitation and associated flow-choking characteristics in poppet valves,” Journal of Zhejiang University SCIENCE A, vol. 2024, no. 6, pp. 1–15, 2024.

S. Wei, C. Lin, and B. Ji, “Large eddy simulation of cavitating flow in a cone valve with special emphasis on the shear cavitation inside and its effects,” Journal of Hydrodynamics, vol. 37, no. 5, pp. 876–891, 2025, doi: 10.1007/s42241-025-0072-8.

Y. S. Liu, Y. Huang, and Z. Y. Li, “Experimental investigation of flow and cavitation characteristics of a two-step throttle in water hydraulic valves,” Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, vol. 216, no. 1, pp. 105–111, 2002.

H. Gao, W. Lin, and T. Tsukiji, “Investigation of cavitation near the orifice of hydraulic valves,” Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, vol. 220, no. 4, pp. 253–265, 2006.

Y. Liu, Y. Yousheng, and Z. Zhuangyun, “Research on the flow and cavitation characteristics of multi-stage throttle in water-hydraulics,” Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, vol. 220, no. 2, pp. 99–108, 2006.

X. Liu, J. He, Z. Long, W. Li, and B. Li, “Effects of structural sizes on characteristics of cavitating flows in a two-step throttle valve,” Journal of Vibration and Shock, vol. 34, no. 23, pp. 143–148, 2015.

S. Nie, G. Huang, Y. Li, Y. Yang, and Y. Zhu, “Research on low cavitation in water hydraulic two-stage throttle poppet valve,” Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, vol. 220, no. 3, pp. 167–179, 2006.

C. Yuan, J. Song, and M. Liu, “Investigation of flow dynamics and governing mechanism of choked flow for cavitating jet in a poppet valve,” International Journal of Heat and Mass Transfer, vol. 129, pp. 113–131, 2019.

G. H. Schnerr and J. Sauer, “Physical and numerical modeling of unsteady cavitation dynamics,” in Proc. 4th Int. Conf. on Multiphase Flow, 2001.

R. F. Kunz, D. A. Boger, D. R. Stinebring, T. S. Chyczewski, J. W. Lindau, H. J. Gibeling, et al., “A preconditioned Navier–Stokes method for two-phase flows with application to cavitation prediction,” Computers & Fluids, vol. 29, no. 8, pp. 849–875, 2000.

S. Oshima, T. Leino, M. Linjama, K. T. Koskinen, and M. J. Vilenius, “Experimental study on cavitation in water hydraulic poppet valve,” Transactions of the Japan Fluid Power System Society, vol. 33, no. 2, pp. 29–35, 2002.

Downloads

Published

2026-11-16

How to Cite

Yuan, C. . (2026). Manipulation Strategy of Vortex Cavitation Evolution in Poppet Valves Through Structure Modification. International Journal of Fluid Power, 27(03), 563–588. https://doi.org/10.13052/ijfp1439-9776.2734

Issue

Section

Original Article