Experimental Investigation Into a Compact Hybrid Direct-Driven and Valve-Controlled Electro-Hydraulic Circuit for Mobile Cranes
DOI:
https://doi.org/10.13052/ijfp1439-9776.2733Keywords:
Hydraulic systems, Mobile machines, Actuation system, Energy Efficiency, Direct Driven HydraulicsAbstract
Despite the ongoing trend toward electrification, hydraulic systems remain the dominant solution for mobile machines’ actuation due to their high power density and robustness. However, conventional systems controlled with directional control valves (DCVs) entail low energy efficiency caused by high throttle losses and lack of energy recuperation.
This paper proposes a hybrid direct-driven and valve-controlled electro-hydraulic actuation system for mobile cranes, with emphasis on compactness and improved energy efficiency. The approach substitutes the valve-based control of the lift cylinder with a direct actuation using a variable-speed electro-hydraulic converter. This converter also supplies the remaining cylinders through conventional proportional DCVs.
The system was experimentally evaluated under laboratory conditions by performing multiple manual loading and unloading cycles. It was compared with a conventional load sensing (LS) system with proportional DCVs. The experimental results demonstrate a significant reduction in energy consumption, with median values of 53.83% during log loading cycles and 62.05% during log unloading cycles compared to the reference LS system.
The fundamental limitation of the system is that the lift cylinder pressure must be the highest in the system. One possible solution is to create counterpressure in its rod-side chamber, which was achieved using a proportional valve. The modified system demonstrated reduced energy savings, with median values of 28.84% during log loading and 46.59% during log unloading compared to the reference LS system.
These findings validate the proposed system for mobile crane actuation and confirm its higher efficiency compared to a conventional system.
Downloads
References
J. Kalmari, J. Backman, and A. Visala, “Coordinated motion of a hydraulic forestry crane and a vehicle using nonlinear model predictive control,” Computers and Electronics in Agriculture, vol. 133, pp. 119–127, 2017.
J. Koivumäki and J. Mattila, “High performance nonlinear motion/force controller design for redundant hydraulic construction crane automation,” Automation in Construction, vol. 51, pp. 59–77, 2015.
Ponsse, “The perfect cut. ctl – the cut-to-length method,” Ponssentie 22, 74200 Vieremä, 2023.
A. Mahmood, S. F. Abedin, M. O’Nils, M. Bergman, and M. Gidlund, “Remote-timber: An outlook for teleoperated forestry with first 5g measurements,” IEEE Industrial Electronics Magazine, vol. 17, no. 3, pp. 42–53, 2023.
V. Waurich, B. Beck, J. Weber, and F. Will, “Levels of digitalization for construction machinery on the connected and automated construction site,” in Construction logistics, equipment, and robotics, (Cham), pp. 157–165, Springer Nature Switzerland, 2024.
G. P. Moreda, M. Muñoz Garcia, and P. Barreiro Elorza, “High voltage electrification of tractor and agricultural machinery – a review,” Energy Conversion and Management, vol. 115, pp. 117–131, 2016.
T. Lin, Q. Wang, B. Hu, and W. Gong, “Development of hybrid powered hydraulic construction machinery,” Automation in Construction, vol. 19, no. 1, pp. 11–19, 2010.
S. Qiao, Y. Hao, L. Quan, L. Ge, and L. Xia, “A novel electro-hydraulic compound driving system with potential energy regeneration capability for lifting device,” IEEE Access, vol. 10, pp. 18248–18256, 2022.
S. Du, J. Zhou, J. Hong, H. Zhao, and S. Ma, “Application and progress of high-efficiency electro-hydrostatic actuator technology with energy recovery: A comprehensive review,” Energy Conversion and Management, vol. 321, pp. 1–24, 2024.
D. Fassbender, C. Brach, and T. Minav, “Energy-efficiency comparison of different implement powertrain concepts to each other and between different heavy-duty mobile machines,” International Journal of Fluid Power, vol. 25, p. 127–144, Jul. 2024.
S. Ketelsen, D. Padovani, T. O. Andersen, M. K. Ebbesen, and L. Schmidt, “Classification and review of pump-controlled differential cylinder drives,” Energies, vol. 12, no. 7, pp. 1–27, 2019.
T. Komarov, D. Zadorozhniuk, H. Handroos, and J. Pyrhönen, “Valve-free operation of the lift cylinder in mobile machines with an electrohydraulic actuation system,” in 2024 IEEE 20th International Conference on Automation Science and Engineering (CASE), pp. 1100–1105, IEEE, 2024.
C. Williamson, J. Zimmerman, and M. Ivantysynova, “Efficiency study of an excavator hydraulic system based on displacement-controlled actuators,” in Bath ASME Symposium on Fluid Power and Motion Control (FPMC2008), pp. 291–307, 2008.
L. Ge, L. Quan, Y. Li, X. Zhang, and J. Yang, “A novel hydraulic excavator boom driving system with high efficiency and potential energy regeneration capability,” Energy Conversion and Management, vol. 166, pp. 308–317, 2018.
L. Schmidt, M. v. Binsbergen-Galán, R. Knöll, M. Riedmann, B. Schneider, and E. Heemskerk, “Energy efficient excavator implement by electro-hydraulic/mechanical drive network,” International Journal of Fluid Power, vol. 25, no. 04, p. 413–438, 2024.
F. Zappaterra, D. Pan, T. Ransegnola, A. Vacca, S. D. Sudhoff, and E. Busquets, “A novel electro-hydraulic unit design based on a shaftless integration of an internal gear machine and a permanent magnet electric machine,” Energy Conversion and Management, vol. 310, pp. 1–23, 2024.
S. Qu, F. Zappaterra, A. Vacca, and E. Busquets, “An electrified boom actuation system with energy regeneration capability driven by a novel electro-hydraulic unit,” Energy Conversion and Management, vol. 293, pp. 1–17, 2023.
E. Busquets and M. Ivantysynova, “Priority-based supervisory controller for a displacement-controlled excavator with pump switching,” in Proceedings of the ASME/BATH 2015 Symposium on Fluid Power and Motion Control, no. V001T01A014 in Fluid Power Systems Technology, 2015.
T. Bekele, R. Åman, and H. Handroos, “The control of multiple actuators using single iehec pump/motor,” in 10th International Fluid Power Conference (10. IFK), pp. 73–88, Nature Publishing Group, 2016.
T. Komarov, V. Zhidchenko, and H. Handroos, “Automatic sequential actuation of multiple cylinders in mobile cranes using a single electro-hydraulic converter,” in The 19th Scandinavian International Conference on Fluid Power, SICFP’25, pp. 1–8, River Publishers, 2025.
S. Qu, Z. Liu, R. Cardoso, and E. Busquets, “A compensator-less load sensing system designed for electrified compact track loader,” International Journal of Fluid Power, vol. 26, p. 187–210, July 2025.
V. Zhidchenko, T. Komarov, A. Williot, N. Bauer, and H. Handroos, “A method for planning the trajectory of mobile hydraulic crane booms with a focus on energy efficiency,” in 2023 IEEE 21st International Conference on Industrial Informatics (INDIN), pp. 1–7, IEEE, 2023.
Parker Hannifin Corporation, Variable Speed Drive – AC30 Series. Parker Hannifin Corporation, 2023.
Parker Hannifin, Hydraulic Pump and Power Systems, GVM Global Vehicle Motor Power Series. Permanent Magnet (PMAC) Motor for Mobile Systems. Parker Hannifin, 2022.
Parker Hannifin, Mobile Controls Division, Catalogue HY17-8249/US – Hydraulic Motor/Pump Series F11/F12. Parker Hannifin, 2004.
S. AG, Product overview PFT. Precise pressure transmitter with flush-mounted process connections for flexible use. SICK AG, 2025.
Danfoss, Proportional Valve Group. Danfoss, 2019.
Bosch Rexroth AG, RE 29121. Bosch Rexroth AG, 2022.
H. Pedersen, T. Andersen, and M. Hansen, “Load sensing systems – a review of the research contributions throughout the last decades,” in Proceedings 4th IFK Workshop, pp. 125–139, 2004.

