Energy and Techno-Economic Analysis of Hydraulic Power Unit Designs for a Coil Compactor Machine

Authors

  • Samuele Nizzardo Department of Industrial Engineering, University of Padova, Via Venezia 1, Padova, 35131, Italy https://orcid.org/0009-0003-2198-1389
  • Alarico Macor Department of Management and Engineering, University of Padova, Via Stradella San Nicola 3, Vicenza, 36100, Italy https://orcid.org/0000-0003-2244-6524
  • Alberto Benato Department of Industrial Engineering, University of Padova, Via Venezia 1, Padova, 35131, Italy https://orcid.org/0000-0002-0122-1353

DOI:

https://doi.org/10.13052/ijfp1439-9776.2735

Keywords:

Hydraulic power unit, coil compactor machine, Energy Efficiency, Techno-economic analysis, Load-sensing system, Hydraulic Accumulator

Abstract

Coil compactor machines are energy-intensive industrial systems in which the hydraulic power unit plays a major role in determining overall efficiency during the operating cycle. This study presents an energy and techno-economic analysis of five hydraulic power unit designs for a wire rod coil compactor machine equipped with a tying head unit. Starting from a conventional pressure-controlled reference system, four alternative architectures are investigated: an inverter-driven system, a load-sensing system, an accumulator-based system, and a split hydraulic layout. Energy consumption is evaluated through detailed simulation of the machine duty cycle, while both operating and initial investment costs are assessed to compare the different solutions on a life-cycle basis. The results show that the load-sensing system and the optimized split system provide the best overall performance, reducing energy consumption by 27.89% and 23.88%, respectively, compared with the reference configuration. These reductions correspond to annual operating cost savings of approximately 4.9 k€ and 4.2 k€, respectively. Although these solutions require higher initial investments (+5.93 k€ for the load-sensing system and +2.72 k€ for the optimized split system), the corresponding simple payback periods are approximately 14.4 months and 7.7 months, respectively. The life-cycle assessment over a 20-year operating horizon indicates a substantial reduction in total expenditure. In particular, cumulative operating costs decrease from approximately 355 k€ for the reference configuration to about 256 k€ and 270 k€ for the load-sensing and optimized split solutions, respectively. The proposed analysis provides quantitative support for the selection of hydraulic power unit designs in energy-intensive industrial machinery and highlights the importance of integrating energy and economic criteria during the design stage.

Downloads

Download data is not yet available.

Author Biographies

Samuele Nizzardo, Department of Industrial Engineering, University of Padova, Via Venezia 1, Padova, 35131, Italy

Samuele Nizzardo. Ph.D. Candidate in Industrial Engineering (Curriculum Energy Engineering) at the University of Padova. He received his master’s degree in aerospace engineering from the University of Padova. His main research interests include fluid topology optimization, fluid mechanics, computational fluid dynamics, and fluid power systems.

Alarico Macor, Department of Management and Engineering, University of Padova, Via Stradella San Nicola 3, Vicenza, 36100, Italy

Alarico Macor. Associate Professor of Hydraulic Systems and Fluid Machines at the Department of Engineering and Management, University of Padova. His main research interests include turbomachinery, energy conversion plants, thermoeconomic analyses, emissions in biodiesel and biogas engines and boilers, fluid power systems, and hydromechanical and hybrid transmissions.

Alberto Benato, Department of Industrial Engineering, University of Padova, Via Venezia 1, Padova, 35131, Italy

Alberto Benato. Associate Professor of Energy Systems and Power Generation at the Department of Industrial Engineering, University of Padova. He received his Ph.D. in industrial engineering, energy engineering curriculum, from the University of Padova. His main research interests include fluid power systems, Carnot batteries, pumped hydro and hybrid storage units, and renewable-based multi-energy systems.

References

NFPA and CCEFP, “Fluid power carbon emissions reduction roadmap: 2030 and 2050 outlook,” 2023. www.nfpa.com/technologyreports.

M. Bhola and G. Wrat, “Energy-efficient hydraulics in heavy machinery: Technologies, challenges, and future directions,” Sustainability 2026, vol. 18, p. 302, 2026.

J. L. Blackburn, G. Reethof, and J. L. Shearer, Fluid Power Control. New York and London: The Technology Press of M.I.T., John Wiley & Sons, Inc., 1960.

H. E. Merritt, Hydraulic Control Systems. New York, London, Sydney: John Wiley & Sons, Inc., 1967.

H. Raduenz, L. Ericson, K. Heybroek, V. J. de Negri, and P. Krus, “Extended analysis of a valve-controlled system with multi-chamber actuator,” International Journal of Fluid Power, vol. 23(1), pp. 79–108, 2022.

L. Darko, K. Mitja, and U. Samo, “Electro-hydraulic load sensing with a speed-controlled hydraulic supply system on forming-machines,” Int J Adv Manuf Technol, vol. 41, pp. 1066–1075, 2009.

H. H. Triet and K. K. Ahn, “Comparison and assessment of a hydraulic energy-saving for hydrostatic drives,” Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering, vol. 255(1), pp. 21–34, 2011.

X. Yan, S. Nie, B. Chen, F. Yin, H. Ji, and Z. Ma, “Strategies to improve the energy efficiency of hydraulic power unit with flywheel energy storage system,” Journal of Energy Storage, vol. 59, p. 106515, 2023.

L. He, Z. Xiaogang, Q. Long, and Z. Hongjuan, “Research on energy consumption of injection molding machine driven by five different types of electro-hydraulic power units,” Journal of Cleaner Production, vol. 242, p. 118355, 2020.

S. Heitzig, S. Sgro, and H. Theissen, “Energy efficiency of hydraulic systems with shared digital pumps,” International Journal of Fluid Power, vol. 13(3), pp. 49–57, 2012.

Y. Xiaopeng, C. Baijin, Y. Fanglong, J. Hui, M. Zhonghai, and N. Songlin, “Energy optimization of main hydraulic system in a forging press by simulation and experimental methods,” Energy, vol. 277, p. 127620, 2023.

X. Lianpeng, Q. Long, G. Lei, and H. Yunxiao, “Energy efficiency analysis of integrated drive and energy recuperation system for hydraulic excavator boom,” Energy Conversion and Management, vol. 156, pp. 680–687, 2018.

A. Macor, A. Benato, A. Rossetti, and Z. Bettio, “Study and simulation of a hydraulic hybrid powertrain,” Energy procedia, vol. 126, pp. 1131–1138, 2017.

C. Yuan, M. Pan, and A. Plummer, “A review of switched inertance hydraulic converter technology,” Journal of Dynamic Systems, Measurement, and Control, vol. 142, p. 050801, 03 2020.

A. C. Mahato and S. K. Ghoshal, “An overview of energy savings approaches on hydraulic drive systems,” International Journal of Fluid Power, vol. 21, no. 1, pp. 81–118, 2018.

A. C. Mahato and S. K. Ghoshal, “Energy-saving strategies on power hydraulic system: An overview,” Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering, vol. 235, no. 2, pp. 147–169, 2021.

European Commission, “Commission regulation (eu) 2019/1781: laying down ecodesign requirements for electric motors and variable speed drives pursuant to directive 2009/125/ec of the european parliament and of the council, amending regulation (ec) no 641/2009 with regard to ecodesign requirements for glandless standalone circulators and glandless circulators integrated in products and repealing commission regulation (ec) no 640/2009,” Official Journal of the European Union, vol. 62, no. L272/74, p. 74, Oct 1, 2019.

G. Rampinelli, A. Krenzinger, and F. Chenlo Romero, “Mathematical models for efficiency of inverters used in grid connected photovoltaic systems,” Renewable and Sustainable Energy Reviews, vol. 34, pp. 578–587, 2014.

G. K. Costa and N. Sepehri, “Understanding overall efficiency of hydrostatic pumps and motors,” International Journal of Fluid Power, vol. 19, no. 2, pp. 106–116, 2018.

N. D. Manring and R. C. Fales, Hydraulic control systems. John Wiley & Sons, Inc, 2019.

B. Xu, M. Xu, J.-h. Zhang, and Q. Su, “Characteristics of volumetric losses and efficiency of axial piston pump with respect to displacement conditions,” Journal of Zhejiang University-SCIENCE A (Appl Phys & Eng), vol. 17, pp. 186–201, 02 2016.

J. Ivantysyn and M. Ivantysynova, Hydrostatic Pumps and Motors: Principles, Design, Performance, Modelling, Analysis, Control and Testing. Tbi edition, Tech Books International, 2003.

N. D. Manring, “Friction forces within the cylinder bores of swash-plate type axial-piston pumps and motors,” Journal of Dynamic Systems, Measurement, and Control, vol. 121, pp. 531–537, 09 1999.

Bosch Rexroth AG, Axial piston variable pump - A10VSO series 32, 2026. Technical Catalog n. RE 92714/2026-03-02.

L. Shang and M. Ivantysynova, “An investigation of design parameters influencing the fluid film behavior in scaled cylinder block/valve plate interface,” in Proceedings of the 9th FPNI Ph.D. Symposium on Fluid Power. Florianópolis, SC, Brazil, p. V001T01A027, 10 2016.

R. Dindorf, J. Takosoglu, and P. Wos, “Review of hydro-pneumatic accumulator models for the study of the energy efficiency of hydraulic systems,” Energies, vol. 16, no. 18, 2023.

Bosch Rexroth AG, Proportional directional valves, pilot operated, with electrical position feedback and integrated electronics (OBE) – Type 4WRKE, 2026. Technical Catalog n. RE 29075/08.13.

Downloads

Published

2026-11-16

How to Cite

Nizzardo, S. ., Macor, A. ., & Benato, A. . (2026). Energy and Techno-Economic Analysis of Hydraulic Power Unit Designs for a Coil Compactor Machine. International Journal of Fluid Power, 27(03), 589–616. https://doi.org/10.13052/ijfp1439-9776.2735

Issue

Section

Original Article