EFFECT OF COMBINING PRECOMPRESSION GROOVES, PCFV AND DCFV ON PUMP NOISE GENERATION

Authors

  • Ganesh Kumar Seeniraj Purdue University, Department of Agricultural and Biological Engineering Maha Fluid Power Research Center, 1500 Kepner Drive, Lafayette, IN 47905, USA
  • Minming Zhao Purdue University, Department of Agricultural and Biological Engineering Maha Fluid Power Research Center, 1500 Kepner Drive, Lafayette, IN 47905, USA
  • Monika Ivantysynova Purdue University, Department of Agricultural and Biological Engineering Maha Fluid Power Research Center, 1500 Kepner Drive, Lafayette, IN 47905, USA

Keywords:

noise reduction, axial piston pump, combination, precompression grooves, precompression filter volume

Abstract

Noise emission from axial piston machines has been studied for several decades by many researchers and pump manufacturers. As a result, different design methods for reducing the sources of pump noise have been proposed and are in use. The authors have studied and compared the effectiveness of several passive design methods. One of the outcomes of the study is the finding that among the passive design methods, precompression grooves and precompression filter volume (PCFV) are most effective in reducing the noise sources in the axial piston machines in a wide range of operating conditions. The limitations of precompression grooves and PCFV are explained and a new design method which combines the precompression grooves, PCFV and decompression filter volume (DCFV) has been proposed. The proposed combination of design methods is parameterized and uses a multi-objective optimization procedure. The effectiveness of the proposed optimization procedure (a combination of precompression grooves, PCFV and DCFV) is demonstrated using simulation results in comparison to precompression grooves and PCFV. The results show that a combination of precompression grooves, PCFV with groove and DCFV with groove, is effective in reducing both the fluid borne noise source (FBNS) and the structure borne noise source (SBNS) simultaneously in an axial piston machine at a wide range of operating conditions. It has also been shown that the proposed method allows noise source reduction without affecting volumetric efficiency.

Downloads

Download data is not yet available.

Author Biographies

Ganesh Kumar Seeniraj, Purdue University, Department of Agricultural and Biological Engineering Maha Fluid Power Research Center, 1500 Kepner Drive, Lafayette, IN 47905, USA

Ganesh Kumar Seeniraj Born on May 10, 1980 in Sivakasi, Tamil Nadu, India. He received his Bachelor of Engineering in Mechanical Engineering from College of Engineering, Guindy, Anna University, India in 2001. He received his MS in Mechanical Engineering from Kettering University, USA in 2003 and PhD from Purdue University, USA in 2009. Improving the efficiency of Fluid Power Systems at both component and system level has been his main research area. His research focus also includes reduction of fluid borne and structure borne noise source in hydraulic pumps/motors and transmissions.

Minming Zhao, Purdue University, Department of Agricultural and Biological Engineering Maha Fluid Power Research Center, 1500 Kepner Drive, Lafayette, IN 47905, USA

Minming Zhao Born on August 21th 1987 in Zhoushan, China. He received his BS degree in Mechanical Engineering in 2010 from Shanghai Jiao Tong University (SJTU), China. He is currently a master student at Purdue University. His main research focuses on configuration and control strategy for hydraulic hybrid transmission and reduction of fluid borne and structure borne noise sources in hydraulic pumps/motors and transmissions.

Monika Ivantysynova, Purdue University, Department of Agricultural and Biological Engineering Maha Fluid Power Research Center, 1500 Kepner Drive, Lafayette, IN 47905, USA

Monika Ivantysynova Born on December 11th 1955 in Polenz (Germany). She received her MSc. Degree in Mechanical Engineering and her PhD. Degree in Fluid Power from the Slovak Technical University of Bratislava, Czechoslovakia. After 7 years in fluid power industry, she returned to university. In April 1996 she received a Professorship in fluid power & control at the University of Duisburg (Germany). From 1999 until August 2004 she was Professor of Mechatronic Systems at the Technical University of Hamburg-Harburg. Since August 2004 she is Professor in Mechanical Engineering and Agricultural and Biological Engineering at Purdue University, USA. She was approved as Maha named Professor in Fluid Power Systems and director of the Maha Fluid Power Research Center at Purdue University in November 2004. Her main research areas are energy saving actuator technology and model based optimization of displacement machines as well as modeling, simulation and testing of fluid power systems. Besides the book “Hydrostatic Pumps and Motors” published in German and English, she has published more than 90 papers in technical journals and at international conferences.

References

Ericson, L. 2008. Flow Pulsations in Fluid Power

Machines – a Measurement and Simulation Study.

PhD thesis. Linkoping University, Linkoping,

Sweden.

Ivantysyn J. and Ivantysynova M. 2001. Hydrostatic

Pumps and Motors. Academic Books International,

New Delhi.

Ivantysynova, M., Seeniraj, G. K. and Huang, C.

Comparison of different valve plate designs

focusing on oscillating forces and flow pulsation.

The Ninth Scandinavian International Conference

on Fluid Power, SICFP '05, Linkoping, Sweden.

Johansson, A. and Palmberg, J. O. 2005. The

importance of suction timing in axial piston pumps.

The ninth Scandinavian International Conference

on Fluid Power, SCIFP ’05, Linkoping, Sweden.

Johansson, A. 2005. Design Principles for Noise

Reduction in Hydraulic Piston Pumps - Simulation,

Optimisation and Experimental Verification. PhD

thesis, Linkoping University, Linkoping, Sweden.

Klop, R. and Ivantysynova, M. 2010. Sound Intensity

Measurements to Investigate Noise Generation of

Hydrostatic Transmissions. Proceedings of the 7th

International Fluid Power Conference Aachen 2010

(7th IFK), Vol. 2, pp. 229 - 242, Aachen, Germany.

Seeniraj, G. K. 2009. Model Based Optimization of

Axial Piston Machines Focusing on Noise and Efficiency.

PhD thesis. Purdue University, Indiana,

USA.

Seeniraj, G. K. and Ivantysynova, M. 2011. A Multiparameter

Multi-objective Approach to Reduce

Pump Noise Generation. International Journal of

Fluid Power, March 2011, 12 (1), pp. 7 - 17.

Downloads

Published

2011-11-01

How to Cite

Seeniraj, G. K., Zhao, M., & Ivantysynova, M. (2011). EFFECT OF COMBINING PRECOMPRESSION GROOVES, PCFV AND DCFV ON PUMP NOISE GENERATION. International Journal of Fluid Power, 12(3), 53–63. Retrieved from https://journals.riverpublishers.com/index.php/IJFP/article/view/463

Issue

2011: Vol 12 Iss 3

Section

Original Article

Most read articles by the same author(s)

<< < 1 2