On the Volumetric Loss Caused by Incomplete Filling with Undissolved Gas in Positive Displacement Pumps: Lumped Parameter Modeling, CFD Comparisons, and Experimental Validations

Authors

  • Dinghao Pan Maha Fluid Power Research Center, Purdue University, IN, USA
  • Andrea Vacca Maha Fluid Power Research Center, Purdue University, IN, USA
  • Venkata Harish Babu Manne Simerics Inc, MI, USA
  • Daniel Gysling CorVera LLC, CT, USA

DOI:

https://doi.org/10.13052/ijfp1439-9776.2622

Keywords:

Incomplete filling of positive displacement pump, undissolved gas measurement, lumped parameter pump model, 1st-order air-release cavitation, equivalent total air, CFD study of pipe transient air releasee

Abstract

The analysis of the incomplete filling behavior of positive displacement machines requires considerations of the air content within the fluid and its dependency with the suction conditions, which are often associated with high uncertainties. This study contributes to this topic by experimentally studying the incomplete filling behavior of a positive displacement pump and presenting a hybrid modeling method for predicting it. The experimental study involved an original pump testing setup able to measure the gas volume fraction by interpreting the sound wave transmission behavior. Experimental results show that under same sub-atmospheric pump inlet pressure, low-speed operation can enhance the incomplete filling. This behavior is found related to the transient air release process in the line connecting the upstream pressure restriction location (which regulates the sub-atmosphere line pressure) to the pump, which is an effect often neglected in similar analyses on positive displacement machines that neglects the effect of the suction line. Based on the experimental study, a hybrid modeling method for predicting the volumetric losses caused by incomplete filling is proposed, where (i) the amount of undissolved gas in the hydraulic circuit upstream the pump is evaluated by a 1st-order gas release formulation, and (ii) the pump volumetric loss due to incomplete filling is simulated with a lumped volume-based pump model (LP pump model) with an gas-equilibrium fluid model with an equivalent total gas determined from step (i). The 1st-order gas release prediction approach was validated by CFD results of sub-atmospheric pipe flows, for a range of gas-release 1st-order time constants. Using a time constant of 8 s and total air of 6 %, the 1st-order formulation was also validated with experiments. The volumetric loss predicted by the LP pump model were found to agree with the measured pump volumetric efficiency at different operating conditions. The proposed hybrid approach presents a useful simulation tool for studying the incomplete filling of positive displacement pumps with sub-atmospheric inlet pressures, with consideration concerning the layout of the suction circuit.

Downloads

Download data is not yet available.

Author Biographies

Dinghao Pan, Maha Fluid Power Research Center, Purdue University, IN, USA

Dinghao Pan, PhD., is currently a research scientist at Maha Fluid Power Research Center at Purdue University. He graduated with his PhD from Purdue University in 2024 with the research focus of developing multi-physics coupled simulation models and numerical methodologies for compensated crescent-type internal gear pumps and external gear pumps. His research interest also involves reduced order tribology modeling and external gear pump modeling.

Andrea Vacca, Maha Fluid Power Research Center, Purdue University, IN, USA

Andrea Vacca, PhD, is the Maha Fluid Power Faculty Chair and director of the Maha Fluid Power Research Center at Purdue University. The focus of Andrea’s research activities has been fluid power since the beginning of his professional career in early 2000s. Significant research contributions range from modeling techniques for fluid power systems and components, new designs for pumps, as well as principles for enhanced performance of hydraulic control systems.

Venkata Harish Babu Manne, Simerics Inc, MI, USA

Venkata Harish Babu Manne, PhD., holds PhD from the Maha Fluid Power Research Center at Purdue University, specializing in Fluid Power, Tribology, and Computational Fluid Dynamics (CFD). With a strong background in research and numerical modeling, Harish has published in Mechanical Systems and Signal Processing and Tribology Transactions. Currently, he is a Project Engineer at Simerics Inc. in Novi, MI, where he applies advanced CFD techniques to solve complex engineering challenges.

Daniel Gysling, CorVera LLC, CT, USA

Daniel Gysling, PhD., is founder and CEO of CorVera, LLC, a company with a charter to improve the measurement of liquids with entrained gas. Daniel’s technical expertise is in the areas of fluid dynamics and structural dynamics. Daniel holds BS in Aerospace Engineering from The Pennsylvania State University, and a PhD in Aeronautics and Astronautics from the Massachusetts Institute of Technology.

References

P. Casoli et al. Modelling of fluid properties in hydraulic positive displacement machines. Simulation Modelling Practice and Theory (2006). https://doi.org/10.1016/j.simpat.2006.09.006.

H. Murrenhoff and K. Schmitz. Fundamentals of Fluid Power. Vol. 7. Reihe Fluidtechnik. Aachen: Shaker Verlag, 2018. isbn: 9783844063066.

J. Ivantysyn and M. Ivantysynova. Hydrostatic Pumps and Motors: Principles, Design, Performance, Modelling, Analysis, Control and Testing. Tech Books International, 2003. isbn: 81-88305-08-1.

A. Vacca and G. Franzoni. Hydraulic fluid power: fundamentals, applications, and circuit design. John Wiley & Sons, 2021. isbn: 978-1-119-56910-7.

P. H. Schweitzer. Effect of Aeration on Gear-Pump Delivery and Lubrication Ceiling. Transactions of the American Society of Mechanical Engineers (1945). https://doi.org/10.1115/1.4018189.

Siemens PLM Software Inc. Simcenter AmesimTM

software User’s guides: AHYD Advanced Fluid Properties Technical bulletin no. 117. 2021.

G. Altare and M. Rundo. Computational Fluid Dynamics Analysis of Gerotor Lubricating Pumps at High-Speed: Geometric Features Influencing the Filling Capability. Journal of Fluids Engineering (2016). https://doi.org/10.1115/1.4033675.

T. Hussain et al. A Simulation Study of Lubricating Oil Pump for an Aero Engine. Journal of Mechanical Engineering (JMechE) (2021). https://doi.org/10.24191/jmeche.v18i3.15417.

A. Corvaglia et al. Simulation and Experimental Activity for the Evaluation of the Filling Capability in External Gear Pumps. Fluids (2023). https://doi.org/10.3390/fluids8090251.

P. Fresia et al. CFD Modelling of an Internal Gear Pump for High Viscosity Fluids. International Design Engineering Technical Conferences and Computers and Information in Engineering Conference 2023. https://doi.org/10.1115/DETC2023-111589.

P. H. Schweitzer and V. G. Szebehely. Gas evolution in liquids and cavitation. Journal of Applied Physics (1950). https://doi.org/10.1063/1.1699579.

H. Pleskun, A. Syring, and A. Brummer. Transient chamber filling in rotary positive displacement vacuum pumps. IOP Conference Series: Materials Science and Engineering (2022). https://doi.org/10.1088/1757-899X/1267/1/012016.

H. Boland and L. Shang. An Analysis of Cavitation Phenomena Scalability in Axial Piston Machine. ASME/BATH 2023 Symposium on Fluid Power and Motion Control 2023. https://doi.org/10.1115/FPMC2023-113585.27.

M. Rundo, G. Altare, and P. Casoli. Simulation of the filling capability in vane pumps. Energies (2019). https://doi.org/10.3390/en12020283.

D. Buono et al. Modelling Approach on a Gerotor Pump Working in Cavitation Conditions. Energy Procedia (2016). https://doi.org/10.1016/j.egypro.2016.11.089.

U. Stuppioni et al. Computational Fluid Dynamics Modeling of Gaseous Cavitation in Lubricating Vane Pumps: On Metering Grooves for Pressure Ripple Optimization. Journal of Fluids Engineering (2022). https://doi.org/10.1115/1.4056416.

F.L. Yin et al. Numerical and experimental study of cavitation performance in sea water hydraulic axial piston pump. Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering (2016). https://doi.org/10.1177/0959651816651547.

A.K. Singhal et al. Mathematical Basis and Validation of the Full Cavitation Model. Journal of Fluids Engineering (2002). https://doi.org/10.1115/1.1486223.

K. Kowalski et al. “Experimental Study on Cavitation-Induced Air Release in Orifice Flows”. Journal of Fluids Engineering (2018). https://doi.org/10.1115/1. 4038730.

H.Q. Yang, A.K. Singhal, and M. Megahed. The full cavitation model. Lecture series – Von Karman Institute for fluid dynamics 4 (2005). purchased on 2020 Sept. from VKI store, p. 10.

U. Stuppioni et al. Computational Fluid Dynamics Modeling of Gaseous Cavitation in Lubricating Vane Pumps: An Approach Based on Dimensional Analysis. Journal of Fluids Engineering (2020). https://doi.org/10.1115/1.4046480.

F. Orlandi, L. Montorsi, and M. Milani. Cavitation analysis through CFD in industrial pumps: A review. International Journal of Thermofluids (2023). https://doi.org/10.1016/j.ijft.2023.100506.

R. Klop, A. Vacca and M. Ivantysynova. A Numerical Approach for the Evaluation of the Effects of Air Release and Vapour Cavitation on Effective Flow Rate of Axial Piston Machines. International Journal of Fluid Power (2010). https://doi.org/10.1080/14399776.2010.10780996.

J. Zhou, A. Vacca, and B. Manhartsgruber. A Novel Approach for the Prediction of Dynamic Features of Air Release and Absorption in Hydraulic Oils. Journal of Fluids Engineering (2013). https://doi.org/10.1115/1.4024864.

Y. G. Shah, A. Vacca, and S. Dabiri. Air Release and Cavitation Modeling with a Lumped Parameter Approach Based on the Rayleigh–Plesset Equation: The Case of an External Gear Pump. Energies (2018). https://doi.org/10.3390/en11123472.28.

Z. Mistry and A. Vacca. Cavitation Modeling Using Lumped Parameter Approach Accounting for Bubble Dynamics and Mass Transport Through the Bubble Interface. Journal of Fluids Engineering (2023). https://doi.org/10.1115/1.4062135.

M. Rundo, R. Squarcini, and F. Furno. Modelling of a Variable Displacement Lubricating Pump with Air Dissolution Dynamics. SAE International Journal of Engines (2018). https://doi.org/10.4271/03-11-02-0008.

Eckerle Technologies GmbH. EIPS segment pump. 2023. url: https://eckerle.com/en/products/eips2-008ra04-1x-s111-eips-segment-pump-industrial-design.

A. B. Wood and R.B. Lindsay. A textbook of sound. 1956.

D. L. Gysling. Accurate mass flow and density of bubbly liquids using speed of sound augmented Coriolis technology. Flow Measurement and Instrumentation (2023). https://doi.org/10.1016/j.flowmeasinst.2023.102358.

Y. Zhang et al. Cavitation optimization of single-orifice plate using CFD method and neighborhood cultivation genetic algorithm. Nuclear Engineering and Technology (2022), https://doi.org/10.1016/j.net.2021.10.043.

A. Simpson and V. V. Ranade. Modelling of hydrodynamic cavitation with orifice: Influence of different orifice designs. Chemical Engineering Research and Design (2018), https://doi.org/10.1016/j.cherd.2018.06.014.

B. Ebrahimi et al. Characterization of high-pressure cavitating flow through a thick orifice plate in a pipe of constant cross section. International Journal of Thermal Sciences (2017), https://doi.org/10.1016/j.ijthermalsci.2017.01.001.

D. Pan and A. Vacca. Total efficiency prediction of crescent type internal gear pump considering floating balancing components. ASME/BATH Symposium on Fluid Power and Motion Control 2023. https://doi.org/10.1115/FPMC2023-111553.

F.W. Ocvirk. Short-bearing approximation for full journal bearings. Tech. rep. NASA Technical Reports NACA-TN-2808, 1952.

D. Pan and A. Vacca. Modeling of crescent-type internal gear pumps considering gear radial micromotion. Chemical Engineering & Technology, special Issue: Digital, Reliable, Sustainable – Recent Innovations in Fluid Power (2022). https://doi.org/10.1002/ceat.202200419.

H. K. Versteeg. An introduction to computational fluid dynamics the finite volume method, 2/E. Pearson Education India, 2007. 29.

Simerics MP+ help document, Physics Modules – Cavitation – Physics – Cavitation Models. Version 6.0.10.

Downloads

Published

2025-07-13

How to Cite

Pan, D. ., Vacca, A. ., Manne, V. H. B. ., & Gysling, D. . (2025). On the Volumetric Loss Caused by Incomplete Filling with Undissolved Gas in Positive Displacement Pumps: Lumped Parameter Modeling, CFD Comparisons, and Experimental Validations. International Journal of Fluid Power, 26(02), 129–162. https://doi.org/10.13052/ijfp1439-9776.2622

Issue

2025: Vol 26 Iss 2

Section

Maha Fluid Power 2024

Most read articles by the same author(s)

1 2 > >>